Focusrite Pro RedNet A16R MkII Remote Controlled Analogue I/O Interface en Londres, Inglaterra, Reino Unido
Nuevo
Doubleclick to zoom in
Contacte al vendedor
para más fotos y información.
Especificaciones
- Condición
- nuevo
- Número de stock
- MONF0017UK
- Input trim
- -78 to 0dB in 1dB steps (per channel)
- Output trim
- -78 to 0dB in 1dB steps (per channel)
- Frequency response
- 20Hz – 20kHz ± 0.1dB
- Thd + n
- ＜-130dB (0.00003%)
- Ein
- -95dBu 'A'-Weighted (typical)
- Signal-to-noise ratio
- 119dB 'A'-Weighted (typical)
- Converter dynamic range
- 120dB 'A'-Weighted (typical), 10Hz – 20kHz
- 0 dbfs reference levels
- +18 or +24dBu (switchable)
- Noise in presence of signal
- -94dBu 'A'-Weighted (typical)
- Dynamic range
- ＞138dB
- Input to output or input
- ＜-100dB unweighted, 20Hz – 20kHz; +23dBu input
- Output to input or output
- ＜-100dB unweighted, 20Hz – 20kHz; -1dBFS input
- Sample rate range
- 32kHz to 216kHz
- Gain error
- -0.3dB
- Latency
- 11 to 45 samples (network and sample rate dependent)
- Supported sample rates
- 44.1 / 48 / 88.2 / 96 / 176.4 / 192 kHz (-4% / -0.1% / +0.1% / +4.167%) at 24 bit
- Clock sources
- Internal, Word Clock, DARS or from Dante Network Master.
- External word clock range
- Nominal sample rate ±7.5%
- Line inputs
- 2 x DB-25 connectors
- Line outputs
- 2 x DB-25 connectors
- Channel count
- 2 x 2 AES3 channels
- Input (optional dars)
- 1 x Female XLR (Switchable with analogue input channels 15 and 16 at quad rates)
- Output
- 1 x Male XLR (Duplicate of analogue output channels 15 and 16 at quad rates)
- Word clock input
- 1 x BNC 75Ω port (switchable termination)
- Word clock output
- 1 x BNC 75Ω port
- Psu
- 2 x Internal, 100-240V, 50/60Hz, consumption 30W
- Network
- 2 x etherCON NE8FBH-S, also compatible with standard RJ45 connectors (Accomodates rugged etherCON NE8MC*. Does not intermate with Cat 6 cable connector NE8MC6-MO and NKE65* cable)
- Primary psu (a)
- Green LED. Illuminates when an AC input is applied and all DC outputs are present.
- Secondary psu (b)
- Green LED. Illuminates when an AC input is applied and all DC outputs are present.
- Primary network
- Green LED. Indicates that a network connection is present on primary port when in redundant mode. When in Switched mode, a valid network connection at either Primary or Secondary network port will cause this LED to illuminate.
- Secondary network
- Green LED. Indicates that a network connection is present on secondary port when in redundant mode. Not used in switched mode.
- Network locked
- Green LED. When unit is network slave, shows valid network lock. When unit is network master, shows lock to internal clock.
- Sample rate
- Orange LED for each: 44.1 kHz, 48 kHz, x2, x4.
- Pull up/down
- Orange LED. Indicates that the unit is set to operate on a Dante pull up/down domain.
- Channel signal level
- 16 Input and 16 Output tri-state signal level LEDs: Green LED (＞ -42dB), Orange LED (＞ -6dB) and Red (＞ 0dB)
- Aes3 signal indicators
- 2 I/O signal indicator LEDs (one input, one output). Green LED illuminates ＞-127dBFS
- Clock source
- Orange LED for each: Internal, Word Clock and DARS
- Redundant
- Allows unit to connect to two independent networks.
- Switched
- Connects both ports to integrated network switch allowing daisy-chaining of devices.
- Operating temperature
- Operates at up to an ambient temperature of 50 degrees Celcius
- Fan
- Two-step Dual Fans which increase in speed when reaching temperatures towards 50 degrees ambient temperature
- 0dbfs reference levels
- +18 or +24dBu (switchable)
- Categoría
- Audiovisual/Broadcast en Reino Unido
- Subcategoría
- Audio
- Subcategoría 2
- Recording
- Subcategoría 3
- Audio interfaces
- Subcategoría 4
- Network audio interfaces
- ID de Anuncio
- 66612905
Descripción
16x16 Analogue I/O With Independent Level Control
RedNet A16R MkII is a 16x16 analogue interface for Dante networks, with channel level control for individual inputs and outputs.
RedNet A16R MkII is a 16-channel analogue Interface for Dante networks, with two channels of AES3 I/O. Individual input and output channel level controls allow for precise adjustment of all I/O levels using RedNet Control. With two power supplies and primary and secondary etherCON network connectors, RedNet A16R MkII is perfect for critical-path applications in recording, post-production, live sound and broadcast. Built-in redundancy features allow for silent fail-over in the event of power or network outage, providing reassurance for system technicians.
Analogue inputs and outputs are connected through four rear-panel AES59-configured DB25 connectors, while an additional pair of AES3 I/O is provided through male and female XLR for added flexibility. The XLR input can accept DARS signals in addition to AES3.
$3,815 USD